Amazon doesn’t permit sending video directly, so if you need to show us the video, please contact us through e-mail, our address is in the attachment. If still can’t work, is better take a video or some photos, to show us your operation steps, should include the whole scene, not partial.
#Laserdrw wood photos software#
Check whether the laser head has returned to the origin after the machine is turned on?Īlso, check those basic installations: machine installation, software installation, connection between PC and machine, whether the switch is turned on, etc. LIMIT SWITCH: is the lid closed while working? Our newest machine no longer installs it. This is a very sensitive component, even though the water is just fine. *The valve may be closed, so the water cut protection function is turned on, causing the laser to be interrupted. If you need operating video, we can send you through e-mail.
Please cut the wiring of the water shutoff protection valve and connect it directly with the machine's wire to form a closed circuit. Please clean this component, it may be blocked by impurities in the water. Please open the lid on the back of the machine, the black and white component that is connected to the water pipe is the water shut off protection valve (as shown the photo). Check the WATER SHOUTOFF PROTECTION VALVE:
If no light, is the problem of the laser power supply.Ģ. Please prese button on your machine, meanwhile, observe if there has light inside the tube. Please check if there is any problem of the tube itself, especially the wiring at both ends. Please check whether there is water in the two layers inside the laser tube to ensure that the water circulation works well. Also check that the focal length of the focus lens has changed and readjust the focal length. Test each reflective lens with double-sided tape and paper to ensure that the laser path is correct. Are the focusing and mirrors dirty or damaged? (If dirty, it is recommended to wipe or replace the lenses.) Abnormal reflective lens sets can also cause the laser to not come out. (In this case, please email us a photo of the damaged part of the laser tube.) We will provide new replacement laser tubes for after-sales service.
#Laserdrw wood photos cracked#
(Laser power supply may be damaged)ģ, if the lens inside the laser tube is clean, or the laser tube is cracked or damaged, the laser tube needs to be replaced. Press the power test button and place a piece of paper at the outlet of the laser tube to check for burn marks. (Make sure the water cycle is clean, otherwise the protective device on the device will activate and limit the emission of the laser tube.) ）Ģ. You need to find your optimal combo.1, whether the cooling water is sufficient, water quality, temperature, water circulation is normal. Test similar design to learn how power and speed relates on your machine, this is different on most K40 and you cannot use the same settings someone else has. Pixel: set this to 1 step, and Repeat to 1 times In the template before, we split engraving and cut in two different layers, this will help you to run the engraving first, and cut later. Method: If you have combined engraving and cut in the same file, you can choose here. I would suggest 12mA power and 10mm/sec to start with. Speed: I have a 3mm acrylic piece in my machine, you may have to test the speed and the power on your machine when testing your cut. Inside first is a good option if you make parts, the machine will cut the inner parts first and then the outer, preventing the part to fall down without the inner holes are cut. Rotate: if you need to rotate or flip your design for mirrored cut/engravings. Now you have this setup box (click to expand)Ĭompany and model is just the data about your machine. Select CUT in the corel menu, the icon marked hereĬlick OK on the data setting, we did this in a earlier step.
You are now ready for your first cut test. Select the box as shown in the picture, and in the top menu you see a line width set to “hairline”. Start with the “rectangle tool” in corel, make a box with the size of your choise, i made a 54x40mm box. You are now ready to start your first test with the machine Next setting is to check your hardware device ID, you can find this on the controller board, se image belowĬheck out the other settings and make sure you have the same on your settings. You can find information about wich board you have on the controller board in your machine. Most important setting is the mainboard, you may need to change this later if your machine operates very slow (a first sign of wrong mainboard selected) When CorelLaser is installed you will find this menu.Ĭontrol your settings so its identical to this screen. You can use this template to start with, it has one engraving layer and one cutting layer.
#Laserdrw wood photos install#
Step 1: Install Corel Draw 12, X4, X8 or similar version.
0 kommentar(er)
